塑性变形是什么意思_塑性变形的翻译_读音_造句_例句

塑性变形

[sù xìng biàn xíng]

n.plastic deformation

v.heave

网络释义:plastic strain; plastic yield; plastic distortion

汉英

网络释义

n.1.plastic deformation2.ductile deformation3.plastic yielding4.plastic flow5.plastic strain6.after flow7.plasticity1.plastic deformation2.ductile deformation3.plastic yielding4.plastic flow5.plastic strain6.after flow7.plasticity

v.1.heave

1.plastic deformation 加速老化- --accelerated ageing 塑性变形- --plastic deformation 塑性流动- --plastic fiow ...

2.plastic strain plastic state 塑性状态 plastic strain 塑性变形 plastic window lights 塑料玻璃 ...

3.plastic yield plastic working 塑性加工 plastic yield 塑性变形 plastic yielding 塑性屈服 ...

4.plastic distortion 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material ...

5.SPD ... afterflaming 补充燃烧 after flow 塑性变形,残余塑性流动 afterheat 余热,后加热 ...

7.ductile deformation Assess 估计 Yielding 塑性变形 Yield strength 抗屈强度 ...

造句带翻译释义:,plastic deformation,heave,plastic strain,plastic yield,plastic distortion

1.This kind of fly line may also be a sort of new deformation form at explosive load in metal.这种飞线可能还是爆炸载荷下金属中出现的一种新的和特殊的塑性变形机制。

2.For the rigid-body model, the fault has no internal deformation, thus the bed remain its length after rotation.刚性旋转时,断块内部没有任何塑性变形,因此地层的长度没有变化。

3.But it is not always proper to analyse all sheet metal forming problems in planar isotropy since most sheet metals are'nt planar isotropic.然而,绝大多数板树为面内异性,因此对所有板材的塑性变形问题一味在面内同性之条件下研究未免就有不妥之处。

4.This paper presented a new technique to determine the elastic-plastic boundary and plastic strains on the surface of metal specimen.据此提出了一种检测试件弹塑性边界和塑性变形程度的新方法。

5.The residual bend results from the plastic deformation imparted as the string is spooled around the radius of the reel and guide arch.在挠性管柱绕着卷筒半径和导拱缠绕时,所给予的塑性变形造成了残留弯曲。

6.The pressure proportional elastic deformation of this bourdon tube is transmitted through a low friction movement to the knife edge pointer.波登管的压力比例塑性变形通过摩擦力很小的机械装置传递给刃形指针。

7.Because loading process has plastic deformation, unloading curve should be used for sensitivity evaluation.因加载过程存在塑性变形,应力敏感性评价应采用卸载曲线。

8.The early research on thermal model of friction stir welding is mainly about the heat of friction, ignoring the heat of plastic deformation.早期的搅拌摩擦焊温度场模型只考虑了摩擦产热,而忽略了塑性变形产热。

9.As shown in Fig. 4. 2, grain flow is the direction of the pattern that the crystals take during plastic deformation.如图4.2所示,晶粒流动的方向就是在塑性变形期间结晶排列的方向。

10.Only a few zinc particles in the coating occurred plastic deformation with irregular orientation.镀层中只有少部分锌粉颗粒发生塑性变形,并且变形取向也无明显的规律。

1/3    1 2 3